Chicagoland MG Club: Tech Tips

Chicagoland MG Club

Chicagoland MG Club

General Tips

MGA Tips

MGB Tips

Midget Tips

MGT Tips

MMM Tips

Tech Session
Photo Archives


  Chicagoland MG Club:Tech Tips

Fuel Tank Slushing and Preparation

Many customers have expressed concern about the additives in modern gasoline breaking down or eating away at fuel tank coating. We followed up on your concerns and have been assured by our supplier that the white-colored sealer he has been providing us for several years is more than capable of withstanding any current gasoline additives. We'll keep you informed if there are any future developments.

To properly apply any sealer, the tank must be scrupulously clean inside. In the past, this was easily achieved by simply taking the tank to a local radiator or engine machine shop and having it dipped. However, many shops today are turning away this type of work due to a variety of environmental issues. To allow you to properly, and safely, clean your gas tank at home we've recently added both a cleaning solution and an etching fluid which should be used together to properly prep your tank for sealing. Both of these products are biodegradable and can be safely used at home .

Most problems with gumming or sealer breakdown can be traced to improper preparation of the tank prior to the application, followed by improper application and draining of the sealer. Here's how to do it the right way .

Getting Started

Before any work can begin, the tank must be completely removed from the car. It's just not possible to properly clean the tank, or apply and drain the slushing compound without first removing the tank. Completely drain all gasoline and thoroughly ventilate the tank by allowing it to air out for several hours. Remove the sending unit, feed lines, and any drain plugs. Remove and replace, if necessary, any tank-mounted fuel filters so they won't clog. Now is also the time to remove any rust or scale from the outside of the tank using a suitable wire brush.

Cleaning

To prepare the tank for etching and slushing, we recommend cleaning it thoroughly with a biodegradable cleaning fluid. Following the directions, use hot water to dilute the solution and slosh it inside the tank in an agitating motion. Drain and repeat as needed until all gum and shellac residue is removed. For very gummy tanks, plug all outlets and allow the solution to sit in the tank, covering the worst areas, for 24 hours. If rust flakes or scale are present, a length of chain can be sloshed around inside the tank with the cleaner, to loosen it up. Our sealer will fill only the slightest pinholes; anything more serious should be considered cause for one of our replacement steel, aluminum, or stainless tanks.

Etching & Sealing

Next, the tank should be etched to provide a good surface for the sealer to adhere. Using etching solution, plug all drains and pour the entire contents in the tank. Slosh it around, covering the entire inside of the tank and let stand for thirty minutes. Repeat the sloshing and let the tank stand for one hour. Drain the tank completely and allow it to air dry thoroughly; overnight is best.

The end is in sight! Now you're ready to apply sealing compound.

Following the directions on the can, plug all drains and pour the entire contents into the tank from the filler neck. Using a back and forth and twisting motion, coat all inside surfaces thoroughly until a thin film is present. Now remove any drain plugs and allow the remaining sealer to thoroughly drain back into the can. Blow compressed air through fuel outlet before flushing compound has a chance to dry and clog fuel pickup! This is particularly important as some applications have a filter screen over the fuel pickup pipe. If anything more than a thin film is applied, the sealer will form a skin over the collected area (usually around baffles) and never completely dry. After a period of time, it will start to break down and clog fuel lines. This is the most common problem we hear about, so be sure and drain the sealer completely off. If thicker coverage is required, allow the sealer to dry for at least 48 hours before reapplying another coat.

The tank should then be left to dry for at least another 48 hours before reinstalling it in the car. Be sure to replace cracked filler-neck hoses and the sending unit gasket if used. All plugs should be reinstalled using thread tape.

You will most likely have more than half of the sealer left over, which can be resealed and used again the next time you want to do the job.

Back to General Tech Tips


©1999, 2001 Chicagoland MG Club, All rights reserved.